Различия

Показаны различия между двумя версиями страницы.

--- start [2023/10/09 08:27] – admin
+++ start [2025/09/16 20:30] (текущий) – [Датчик температуры DS18B20] admin
@@ Строка 1: / Строка 1: @@
 ====== ESP32 ======
+===== ESP32 S2 mini =====
+https://www.wemos.cc/en/latest/s2/s2_mini.html#documentation
+==== Размеры ====
+{{ ::s2-mini-size.png?nolink |}}
+==== Спецификация ====
+based ESP32-S2FN4R2 WIFI IC
+  * Type-C USB
+  * 4MB Flash
+  * 2MB PSRAM
+  * 27x IO
+  * ADC, DAC, I2C, SPI, UART, USB OTG
+  * Compatible with LOLIN D1 mini shields
+  * Compatible with MicroPython, Arduino, CircuitPython and ESP-IDF
+  * Default firmware: MicroPython
+|Operating Voltage|3.3V|
+|Digital I/O Pins|27|
+|Clock Speed|240MHz|
+|Flash|4M Bytes|
+|PSRAM|2M Bytes|
+|Size|34.3*25.4mm|
+|Weight|2.4g|
+==== Распиновка ====
+{{ :s2_mini_pin.jpg?nolink |}}
 ===== ESP32-wroom-32 30pin =====
@@ Строка 5: / Строка 32: @@
 {{:esp32-wroom-wifi-devkit-v1_pinout.png|}}
 ==== Принципиальная схема ====
@@ Строка 15: / Строка 45: @@
 ===== Прошивка =====
-. Запустить flash_download_tool
+# Запустить flash_download_tool
-. В первой строке выбрать прошивку (bin), установить галочку и адрес смещения установить "0"
-. Подключить питание к модулю при нажатой кнопке boot
-. Нажать кнопук "START"
-. Перезагрузить модуль по питанию.
-. Подключиться к новой сети WiFi. Пароль по умолчанию "configesp"
-configesp
+# В первой строке выбрать прошивку (bin), установить галочку и адрес смещения установить "0"
+# Подключить питание к модулю при нажатой кнопке boot
+# Нажать кнопку "START"
+# Перезагрузить модуль по питанию
+# Подключиться к новой сети WiFi. Пароль по умолчанию "configesp"
+# Настроить подключение к сети wifi http://192.168.4.1/config
+# Перезагрузить модуль
+====== ESP8266 ======
 ===== ESP8266 wemos d1 mini =====
+==== Распиновка ====
+{{:esp8266_wemos-d1-mini.png?direct&600|}}
+====== Датчики ======
+===== Датчик тока sct013  =====
+{{::sct-013-000.png?direct&600|}}
+{{::sct-013-000_2.png?direct&600|}}
+====== DC UPS Power module ======
+{{ ::dcups.png?direct&600 |}}
+J1: battery interface (battery positive and negative) 5557-2P
+J2: Input power interface 5557-4P
+J3: Output power interface 5557-4P
+J4: Mainboard on/off control output. When used as a backup power supply for the computer, the module can control the mainboard switch through J4, and send instructions to the mainboard to shut down when the battery is undervoltage.
+J5, J7:
+  J7 open circuit: J5 is closed to start the power supply, disconnected to close the power supply, each time the power is turned on, J5 must be disconnected and closed again to turn on the power.
+  J7 short circuit: J5 is closed to start the power supply, and when it is disconnected, the power supply is turned off. When the power is turned on, the power supply is automatically turned on as long as J5 is closed.
+  J7 is open by default
+Users can choose a suitable starting method according to actual practical requirements
+J6: Delay setting jumper (this jumper is only used when the load is the computer motherboard, and it is not set in other situations (ie mode 0)
+J8: The external lead-out terminals of LED1-LED3, lead from this socket when external LEDs are required.
+VR1: Charging current adjustment potentiometer
+VR2: charging voltage adjustment potentiometer
+VR3: Battery start threshold voltage adjustment potentiometer (порогового напряжения запуска аккумулятора)
+VR4: Battery undervoltage protection threshold voltage adjustment potentiometer (порогового напряжения защиты от пониженного напряжения аккумулятора)
+VR5: Output voltage adjustment potentiometer
+LED1: Input power indicator, blue. On when the input power is normal
+LED2: After the charging is completed, the light is on, red, and it goes out during charging
+LED3: This light is on during charging, green, and goes out after charging. When the battery is discharged and the battery voltage drops below the start threshold voltage VSTART, this light flashes. When the battery voltage is lower than the undervoltage protection threshold voltage VUVP, when the power is turned on, the power cannot be started, and the light flashes twice, indicating that the battery is undervoltage.
+LED4: Output voltage indicator, red, on when there is output voltage, and off when the output is off
+Instructions for use
+====== Датчики ======
+===== Распиновка =====
+==== Датчики I2C на GX12 4P ====
+{{::i2c-gx12-4p.png?200|}}
+. GND (бело-оранжевый)
+. VCC (оранжевый)
+. SDA (бело-синий)
+. SCL (синий)
+==== Датчики I2C на «SM2.54» 4pin ====
+{{:i2c-sm2.54.png?200|}}
+Черный   - 0
+Красный  – VCC
+Белый  - SDA
+Желтый  - SCL
+==== Датчик температуры DS18B20 ====
+**Jack 3.5**
+{{:ds18b20-jack35.png?200|}}
+**GX12-3p**
+{{:ds18b20-gx12-3p.png?200|}}
+. GND
+. DATA
+. VCC